Three major operating precautions for hydraulic lifting platform

 

Hydraulic lifting platform

 

Hydraulic lifting platform

 

One, ZF HYDRAULIC hydraulic lifting platform operating procedures

 

1. The lifting platform has been strictly tested before leaving the factory. Adjusting the pressure regulating valve arbitrarily will cause the system to operate abnormally. Non-professionals are not allowed to adjust the pressure regulator valve.

 

2, before using the platform to carefully check the hydraulic and electrical systems, no leakage or bare phenomenon, the joints and fasteners are not loose before use.

 

3. The lifting platform must support the expenditure leg when working. It is appropriate to draw the black and red boundary line. Try to get the maximum support area as much as possible. Adjust the height of the support leg so that the platform level (taking the walking wheel to leave the ground), if necessary, Use a sleeper.

 

4. Turn on the power and start the motor for no-load lifting. Check the load of the hydraulic system after normal use.

 

5. The center of gravity of the load should be at the center of the work surface. Both ends of the guard rails should be locked and locked before working.

 

6. The lifting platform should work strictly according to its prescribed carrying capacity. Overloading work may result in damage to personnel and equipment. It is strictly forbidden for the operator to walk or shake during the ascent and descent of the lifting platform.

 

7. There is abnormal sound when the lifting platform is working, and it should be stopped immediately to avoid damage to equipment and personnel.

 

8. After the work is completed, lower the platform, cut off the power supply, close the legs, and push the platform to the designated position.

 

Hydraulic lifting platform

 

Hydraulic lifting platform

 

Two ZF HYDRAULIC hydraulic lifting platform safety procedures

 

1. It is forbidden to work at heights without supporting or supporting legs.

 

2. It is forbidden to perform aerial work while the lift platform is moving.

 

3. The prohibition of high-altitude operations requiring live operation.

 

4. It is forbidden to work at heights above the rated load.

 

5. Non-electrical professionals are not allowed to dismantle and install electrical appliances to prevent electric shock or misconnection.

 

6. When the elevator platform is in the ascending state, it enters the interior of the elevator platform and must be lifted to lift the platform table to prevent the elevator platform from falling by itself and causing casualties.

 

7. Disassembly of any part of the hydraulic system must be performed in a fully depressurized state.

 

8. Pay attention to the surrounding environment and avoid collision with wires, electrical equipment and other facilities.

 

9. The working condition is that the wind power is not greater than 6 and the load on the table shall not be greater than the rated load.

 

10. Before starting, check whether the platform is in good condition and whether the guardrail and other safety devices are in good condition.

 

11. When the lift is raised, the operator must pay close attention to the distance from the upper object to avoid hitting the body from a height.

 

12. After the lift is raised to a suitable height, the lift is attached to the upper object by a rope in a place where conditions permit. If necessary, the staff should wear a seatbelt to avoid excessive shaking.

 

13. When the elevator is in a position to move or walk, the lifting platform must be reduced to a minimum, and the four legs of the elevator must be retracted.

 

14. For winds higher than Grade 6 it is forbidden to use lifts.

 

15. When the elevator is working, people are not allowed to stand within 2 meters to prevent falling objects and hurt people.

 

16, all structural parts shall not have serious off the weld, deformation, corrosion and disconnection, cracks, etc., Gaotai operators should be wearing seat belts.

 

17. The lift must have at least two operators to operate. It should be guarded when operating, and the guard must be firmly secured.

 

18, to operate smoothly when lifting, at any time to pay attention to the above situation, to prevent tools from falling and hurting people.

 

19. If any abnormality or oil leakage is found, it shall be suspended. The relevant unit shall be promptly commissioned to repair and shall not be sickly used.

 

III. Emergency descent of ZF HYDRAULIC hydraulic lifting platform

 

Attention! Use only in emergency. This function can be performed when the personnel on the elevating platform are suddenly working out of power or the elevating platform is suddenly failed, so that the elevating platform cannot be lowered. Use a screwdriver or other tools to hold the spool of the support valve, and then press the spool inward. The hydraulic oil will automatically depressurize and the cylinder will return oil. The platform will fall on its own weight until it reaches its original height.

 

The above three points describe the three major precautions of the hydraulic lifting platform. If you are the operator of the hydraulic lifting platform, Xiao Bian reminds you that you must follow the labeling of your operation flow to ensure safety first.

The above:Accumulator Repair Guide